Best Way to Build Wooden Adirondack Chair

Written by Stephen

On November 7, 2019
How to build adirondack wooden chair

An adirondack chair located on the patio or in the garden is one of the best places in a home to relax after a long, tiring day. One of the most relaxing chairs that you will find for your home today, the adirondack chair has a classic wooden look and graceful curves that make it super comfortable.

In addition to the above, adirondack chairs are portable, making it easy to remove them from sight when not needed. Now, you have two options to get access to these extremely comfortable chairs; you can either buy these chairs or build them at home. While the first option is definitely more convenient, you can save a lot of money by opting for a DIY adirondack chair. However, it is important for you to learn how to build an adirondack chair.

The easiest way to do that is by referring to the best plans. By going through these plans, you will learn how to make adirondack chairs. So, without wasting any further time, let’s get to the best adirondack chair plans that you can use to build the chair.

1. The Lowes Challenge Chair

The Lowes Challenge Chair is a great DIY option for adirondack chair if you want to build a comfortable chair where you can relax. To build this chair, you will need to follow the plan that includes all the material and instructions for building the Lowes Challenge Chair.

The Supplies You Will Need

  • 60 deck screws sized 1 1/2″
  • A set of sockets
  • 10 carriage bolts with washers and flat nuts sized 2″ X 1/4″
  • Level
  • 2 pressure treated lumber sized 12 ft 1 X 6
  • 1 treated lumber sized 10 ft 1 x 4
  • 1 treated lumber sized 8 ft 1 x 4

Step-by-Step Instructions to Build An Adirondack Chair

  • Using the carriage bolts, join together the legs
  • After assembling the legs, screw the cross piece for the front between the legs in the front
  • Screw the back legs and bottom support together
  • Screw the supports for the arm to each leg in the front
  • To ensure the wood does not split, drill pilot holes
  • Screw on the chair’s arms onto the legs at the front
  • Drill pilot holes once more and follow this up with a bolt on the support piece for the back seat
  • Screw the middle piece for the back onto the chair. Before attaching, ensure that both the vertical back piece and the arms are leveled
  • Screw the remaining two pieces for the back. Ensure that the arms are leveled and the slates are evenly spaced
  • Screw on the pieces that remain evenly
  • Screw on seat slats to complete the job

2. The Pallet Wood Chair

The Pallet Wood Chair is one of the most comfortable and inexpensive DIY adirondack chairs and can be the perfect place in your home to relax. If you want to build this chair, then follow these instructions for building the Pallet Wood Chair.

The Supplies and Tools You Will Need

  • Two 30” square full pallets
  • Multiple sandpaper grits
  • Four 12” long support boards
  • Screws of 3-inches
  • 2-inch screws
  • Drill bit of size 1/8-inch
  • Four 24” long pallet support boards for the legs
  • Three 35 1/2 “support boards
  • 4-inch screws
  • Tape measure
  • Palm sander (optional)
  • Reciprocating saw
  • Carpenter’s square
  • Handsaw or miter
  • Drill without cord
  • Mallet or hammer

Step-by-Step Instructions

  • Using the reciprocating saw, measure, and cut the full pallets if needed
  • Cut the four support boards using a handsaw or miter
  • Insert the cut support boards into the pallet slat’s open sides. This is slat that you will utilize for the seat. To put the support boards into place, you may need to use a mallet or hammer
  • Attach the support pieces using the 2” screws and the cordless drill. Drill the slats of the pallets into every new piece. This should be two screws per piece from both the pallet’s top and bottom. Using the 1/8” drill, drill pilot holes to ensure the platter slats do not split. However, doing this is not necessary.
  • Cut the four pallet support boards by using a handsaw or miter. These boards will be used for the legs
  • Measure and mark 15” up the inside of your leg support boards. Use a tape measure to do this
  • Put the two legs on the ground about thirty inches apart. The mark should face one another and should line up the pallet’s top for the seat with your marks. Line up the pallet’s each side with each leg’s inner edge. End by comparing the square with your carpenter’s square

3. Simple Adirondack Chair

One of the easiest ways to start learning about this chair is by building one that is simple to make. Following is the list of supplies and instructions to build this adirondack chair.

The Supplies You Will Need

  • Wood
  • Trigger clamps
  • Sawhorse
  • Electric drill
  • Jig saw (porter cable and Ryobi)
  • Orbital sander
  • Spindle sander
  • Scroll saw
  • Screws

Step-by-Step Instructions

  • Start by positioning the wood on a sawhorse. This is to ensure that you don’t have to bend over while working constantly
  • Lightly spray an adhesive spray over the wood
  • Using the cordless jigsaw, cut the pattern for the adirondack chair
  • Once you have cut the pattern, use an electric drill, clamps, and screws to join together the different wood pieces to build the chair

These are some of the best ways to build an adirondack chair for Patio and Yards. By going through the above-mentioned printable adirondack chair plans, you will be able to learn how to make adirondack chairs. You can always look for free plans to get started anytime.

TedsWoodworking Plans and Projects

You May Also Like…

Best 5 Belt Sander Tools Review

Best 5 Belt Sander Tools Review

Our woodworking tool reviews offer the kind of insight only a professional craftsman can give. These reviews and reports on popular brand-name woodworking tools provide our visitors with the knowledge they need to make smart tool-buying decisions....

read more
Subscribe to Download Free Plans!

Subscribe to Download Free Plans!

Join our mailing list to receive the updates about free woodworking plans.

You have Successfully Subscribed!